During a sector erase (but not a chip erase), the embeded erase program
can be suspended. Once suspended, the sectors not selected for erasure
may be read and programmed. Autoselect mode is allowed during erase
suspend mode. Presumably, CFI queries are similarly allowed so this
commit allows them as well.
Since guest firmware can use status bits DQ7, DQ6, DQ3, and DQ2 to
determine the current state of sector erasure, these bits are properly
implemented.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-10-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
After two unlock cycles and a sector erase command, the AMD flash chips
start a 50 us erase time out. Any additional sector erase commands add a
sector to be erased and restart the 50 us timeout. During the timeout,
status bit DQ3 is cleared. After the time out, DQ3 is asserted during
erasure.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-9-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
When the flash device is performing a chip erase, all commands are
ignored. When it is performing a sector erase, only the erase suspend
command is valid, which is currently not supported.
In particular, the reset command should not cause the device to reset to
read array mode while programming is on going.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-8-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-6-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Rebased, add assert() on pri_offset]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Manufacturers are allowed to move the PRI table, this is why the
offset is queryable via fixed offsets 0x15/0x16.
Add a variable to hold the offset, so it will be easier to later
move the PRI table.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-17-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The pflash_read()/pflash_write() can check the device endianess
via the pfl->be variable, so remove the 'int be' argument.
Since the big/little MemoryRegionOps are now identical, it is
pointless to declare them both. Unify them.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch to ease review]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Pull out all of the code to modify the status into simple helper
functions. Status handling becomes more complex once multiple
chips are interleaved to produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-3-stephen.checkoway@oberlin.edu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Extracted from bigger patch]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Test the AMD command set for parallel flash chips. This test uses an
ARM musicpal board with a pflash drive to test the following list of
currently-supported commands.
- Autoselect
- CFI
- Sector erase
- Chip erase
- Program
- Unlock bypass
- Reset
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Message-Id: <20190426162624.55977-2-stephen.checkoway@oberlin.edu>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: reworded the patch subject, g_assert_cmpint -> cmphex]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
MIPS queue for June 2016th, 2019
# gpg: Signature made Wed 26 Jun 2019 12:38:58 BST
# gpg: using RSA key D4972A8967F75A65
# gpg: Good signature from "Aleksandar Markovic <amarkovic@wavecomp.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8526 FBF1 5DA3 811F 4A01 DD75 D497 2A89 67F7 5A65
* remotes/amarkovic/tags/mips-queue-jun-26-2019:
target/mips: Fix big endian host behavior for interleave MSA instructions
tests/tcg: target/mips: Fix some test cases for pack MSA instructions
tests/tcg: target/mips: Add support for MSA MIPS32R6 testings
tests/tcg: target/mips: Add support for MSA big-endian target testings
tests/tcg: target/mips: Amend tests for MSA int multiply instructions
tests/tcg: target/mips: Amend tests for MSA int dot product instructions
tests/tcg: target/mips: Add tests for MSA move instructions
tests/tcg: target/mips: Add tests for MSA bit move instructions
dma/rc4030: Minor code style cleanup
dma/rc4030: Fix off-by-one error in specified memory region size
hw/mips/gt64xxx_pci: Align the pci0-mem size
hw/mips/gt64xxx_pci: Convert debug printf()s to trace events
hw/mips/gt64xxx_pci: Use qemu_log_mask() instead of debug printf()
hw/mips/gt64xxx_pci: Fix 'spaces' coding style issues
hw/mips/gt64xxx_pci: Fix 'braces' coding style issues
hw/mips/gt64xxx_pci: Fix 'tabs' coding style issues
hw/mips/gt64xxx_pci: Fix multiline comment syntax
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Xen queue
* Fix build
* xen-block: support feature-large-sector-size
* xen-block: Support IOThread polling for PV shared rings
* Avoid usage of a VLA
* Cleanup Xen headers usage
# gpg: Signature made Mon 24 Jun 2019 16:30:32 BST
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20190624:
xen: Import other xen/io/*.h
Revert xen/io/ring.h of "Clean up a few header guard symbols"
xen: Drop includes of xen/hvm/params.h
xen: Avoid VLA
xen-bus / xen-block: add support for event channel polling
xen-bus: allow AioContext to be specified for each event channel
xen-bus: use a separate fd for each event channel
xen-block: support feature-large-sector-size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Block patches:
- The SSH block driver now uses libssh instead of libssh2
- The VMDK block driver gets read-only support for the seSparse
subformat
- Various fixes
# gpg: Signature made Mon 24 Jun 2019 15:42:56 BST
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-06-24:
iotests: Fix 205 for concurrent runs
ssh: switch from libssh2 to libssh
vmdk: Add read-only support for seSparse snapshots
vmdk: Reduce the max bound for L1 table size
vmdk: Fix comment regarding max l1_size coverage
iotest 134: test cluster-misaligned encrypted write
blockdev: enable non-root nodes for transaction drive-backup source
nvme: do not advertise support for unsupported arbitration mechanism
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sem_timedwait function has been annotated as requiring
non-null args in latest header files from GCC snapshot
representing the future 2.30 release.
This causes configure to fail when -Werror is used:
config-temp/qemu-conf.c: In function ‘main’:
config-temp/qemu-conf.c:2:25: error: null argument where non-null required (argument 1) [-Werror=nonnull]
2 | int main(void) { return sem_timedwait(0, 0); }
| ^~~~~~~~~~~~~
config-temp/qemu-conf.c:2:25: error: null argument where non-null required (argument 2) [-Werror=nonnull]
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190617114114.24897-1-berrange@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The configure script breaks when the qemu source directory is in a path
containing white spaces, in particular the list of targets is not
correctly generated when calling "./configure --help" because of how the
default_target_list variable is built.
In addition to that, *building* qemu from a directory with spaces breaks
some assumptions in the Makefiles, even if the original source path does
not contain spaces like in the case of an out-of-tree build, or when
symlinks are involved.
To avoid these issues, refuse to run the configure script and the
Makefile if there are spaces or colons in the source path or the build
path, taking as inspiration what the kbuild system in linux does.
Buglink: https://bugs.launchpad.net/qemu/+bug/1817345
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Antonio Ospite <antonio.ospite@collabora.com>
Message-Id: <20190526144747.30019-3-ao2@ao2.it>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since commit 79d77bcd36 (configure: Remove --source-path option,
2019-04-29) source_path cannot be overridden anymore, move it out of the
"default parameters" block since the word "default" may suggest that the
value can change, while in fact it does not.
While at it, only set source_path once and separate the positional
argument of basename with "--" to more robustly cover the case of path
names starting with a dash.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Antonio Ospite <antonio.ospite@collabora.com>
Message-Id: <20190526144747.30019-2-ao2@ao2.it>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This interface has been introduced in 2005 with the
coldfire implementation (e6e5906b6e ColdFire target.)
and looks like to do what the linux-user interface already
does with the TRAP exception rather than the ILLEGAL
exception.
This interface has not been maintained since that.
The semi-hosting interface is not removed so coldfire kernel
with semi-hosting is always supported.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190524162049.806-1-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The register request via gdbstub would return the SR part
which contains the Trace/Master/IRQ state flags, but
would be missing the CR (Condition Register) state bits.
This fix adds this support by merging them in the m68k
specific gdbstub handler m68k_cpu_gdb_read_register for SR register.
Signed-off-by: Lucien Murray-Pitts <lucienmp.qemu@gmail.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20190609105154.GA16755@localhost.localdomain>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>