The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Setting errp = NULL is wrong: the automatic error propagation still
propagates the dangling pointer _auto_errp_prop.local_err. We need to
set *errp = NULL to clear the dangling pointer.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210125132635.1253219-1-armbru@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
RISC-V PR for 6.0
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
# gpg: Signature made Thu 04 Mar 2021 14:44:31 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210304:
hw/riscv: virt: Map high mmio for PCIe
hw/riscv: virt: Limit RAM size in a 32-bit system
hw/riscv: virt: Drop the 'link_up' parameter of gpex_pcie_init()
hw/riscv: Drop 'struct MemmapEntry'
MAINTAINERS: Add a SiFive machine section
goldfish_rtc: re-arm the alarm after migration
docs/system: riscv: Add documentation for sifive_u machine
docs/system: Add RISC-V documentation
docs/system: Sort targets in alphabetical order
hw/riscv: sifive_u: Change SIFIVE_U_GEM_IRQ to decimal value
hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
hw/riscv: sifive_u: Add QSPI0 controller and connect a flash
hw/ssi: Add SiFive SPI controller support
hw/block: m25p80: Add various ISSI flash information
hw/block: m25p80: Add ISSI SPI flash support
target-riscv: support QMP dump-guest-memory
roms/opensbi: Upgrade from v0.8 to v0.9
hw/misc: sifive_u_otp: Use error_report() when block operation fails
target/riscv: Declare csr_ops[] with a known size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds detailed documentation for RISC-V `sifive_u` machine,
including the following information:
- Supported devices
- Hardware configuration information
- Boot options
- Machine-specific options
- Running Linux kernel
- Running VxWorks kernel
- Running U-Boot, and with an alternate configuration
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-id: 20210126060007.12904-10-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
virtiofs minor security fix
Fix xattrmap to drop remapped security.capability capabilities.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Thu 04 Mar 2021 10:36:45 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert-gitlab/tags/pull-virtiofs-20210304:
virtiofs: drop remapped security.capability xattr as needed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On Linux, the 'security.capability' xattr holds a set of
capabilities that can change when an executable is run, giving
a limited form of privilege escalation to those programs that
the writer of the file deemed worthy.
Any write causes the 'security.capability' xattr to be dropped,
stopping anyone from gaining privilege by modifying a blessed
file.
Fuse relies on the daemon to do this dropping, and in turn the
daemon relies on the host kernel to drop the xattr for it. However,
with the addition of -o xattrmap, the xattr that the guest
stores its capabilities in is now not the same as the one that
the host kernel automatically clears.
Where the mapping changes 'security.capability', explicitly clear
the remapped name to preserve the same behaviour.
This bug is assigned CVE-2021-20263.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Vivek Goyal <vgoyal@redhat.com>
A pwrite() call returns the number of bytes written (or -1 on error),
and vfio-ccw compares this number with the size of the region to
determine if an error had occurred or not.
If they are not equal, this is a failure and the errno is used to
determine exactly how things failed. An errno of zero is possible
(though unlikely) in this situation and would be translated to a
successful operation.
If they ARE equal, the ret_code field is read from the region to
determine how to proceed. While the kernel sets the ret_code field
as necessary, the region and thus this field is not "written back"
to the user. So the value can only be what it was initialized to,
which is zero.
So, let's convert an unexpected length with errno of zero to a
return code of -EFAULT, and explicitly set an expected length to
a return code of zero. This will be a little safer and clearer.
Suggested-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Message-Id: <20210303160739.2179378-1-farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The Measurement Block Origin inside the SCHIB is used when
Measurement Block format 1 is in used and must be aligned
on 64 bytes otherwise an operand exception is recognized
when issuing the Modify Sub CHannel (MSCH) instruction.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1613741973-3711-2-git-send-email-pmorel@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The virtio standard specifies that any non-transitional device must
reject commands prior to revision setting (which we do). Devices
that are transitional need to assume revision 0 (legacy) if the
driver sends a non-revision-setting command first in order to
support legacy drivers. We neglected to do the latter.
Fortunately, nearly everything worked as intended anyway; the only
problem was not properly rejecting revision setting after some other
command had been issued. Easy to fix by setting revision to 0 if
we see a non-revision command on a legacy-capable revision-less
device.
Found by code inspection, not observed in the wild.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210216111830.1087847-1-cohuck@redhat.com>
Mark Cave-Ayland