Support the writes to the status register so that guest can reset the
EventOverflow, EventLogInt, ComWaitIntr, etc bits after servicing the
respective interrupt.
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250801060507.3382-6-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
amdvi_write*() function do not preserve the older values of W1C bits in
the MMIO register. This results in all W1C bits set to 0, when guest
tries to reset a single bit by writing 1 to it. Fix this by preserving
W1C bits in the old value of the MMIO register.
Fixes: d29a09ca68 ("hw/i386: Introduce AMD IOMMU")
Suggested-by: Ethan MILON <ethan.milon@eviden.com>
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Message-Id: <20250801060507.3382-5-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Setting up IOAPIC memory region requires mr_sys and mr_ir. Currently
these two memory regions are setup after the initializing the IOAPIC
memory region, which cause `amdvi_host_dma_iommu()` to use unitialized
mr_sys and mr_ir.
Move the IOAPIC memory region initialization to the end in order to use
the mr_sys and mr_ir regions after they are fully initialized.
Fixes: 577c470f43 ("x86_iommu/amd: Prepare for interrupt remap support")
Signed-off-by: Sairaj Kodilkar <sarunkod@amd.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Message-Id: <20250801060507.3382-4-sarunkod@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fix issues in PCIe SR-IOV configuration register handling that caused
inconsistent internal state due to improper write mask handling and
incorrect migration behavior.
Two main problems were identified:
1. VF Enable bit write mask handling:
pcie_sriov_config_write() incorrectly assumed that its val parameter
was already masked, causing it to ignore the actual write mask.
This led to the VF Enable bit being processed even when masked,
resulting in incorrect VF registration/unregistration. It is
identified as CVE-2025-54567.
2. Migration state inconsistency:
pcie_sriov_pf_post_load() unconditionally called register_vfs()
regardless of the VF Enable bit state, creating inconsistent
internal state when VFs should not be enabled. Additionally,
it failed to properly update the NumVFs write mask based on
the current configuration. It is identified as CVE-2025-54566.
Root cause analysis revealed that both functions relied on incorrect
special-case assumptions instead of properly reading and consuming
the actual configuration values. This change introduces a unified
consume_config() function that reads actual configuration values and
synchronize the internal state without special-case assumptions.
The solution only adds register read overhead in non-hot-path code
while ensuring correct SR-IOV state management across configuration
writes and migration scenarios.
Fixes: 5e7dd17e43 ("pcie_sriov: Remove num_vfs from PCIESriovPF")
Fixes: f9efcd4711 ("pcie_sriov: Register VFs after migration")
Fixes: CVE-2025-54566
Fixes: CVE-2025-54567
Cc: qemu-stable@nongnu.org
Reported-by: Corentin BAYET <corentin.bayet@reversetactics.com>
Signed-off-by: Akihiko Odaki <odaki@rsg.ci.i.u-tokyo.ac.jp>
Message-Id: <20250727-wmask-v2-1-394910b1c0b6@rsg.ci.i.u-tokyo.ac.jp>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Problem
-------
The expected initial state of the table depends on feature negotiation:
With VIRTIO_NET_F_CTRL_VLAN:
The table must be empty in accordance with the specification.
Without VIRTIO_NET_F_CTRL_VLAN:
The table must be filled to permit all VLAN traffic.
Prior to commit 06b636a1e2 ("virtio-net: do not reset vlan filtering
at set_features"), virtio_net_set_features() always reset the VLAN
table. That commit changed the behavior to skip table reset when
VIRTIO_NET_F_CTRL_VLAN was negotiated, assuming the table would be
properly cleared during device reset and remain stable.
However, this assumption breaks when a driver renegotiates features:
1. Initial negotiation without VIRTIO_NET_F_CTRL_VLAN (table filled)
2. Renegotiation with VIRTIO_NET_F_CTRL_VLAN (table will not be cleared)
The problem was exacerbated by commit 0caed25cd1 ("virtio: Call
set_features during reset"), which triggered virtio_net_set_features()
during device reset, exposing the bug whenever VIRTIO_NET_F_CTRL_VLAN
was negotiated after a device reset.
Solution
--------
Fix the issue by initializing the table when virtio_net_set_features()
is called to change the VIRTIO_NET_F_CTRL_VLAN bit of
vdev->guest_features.
This approach ensures the correct table state regardless of feature
negotiation sequence by performing initialization in
virtio_net_set_features() as QEMU did prior to commit 06b636a1e2
("virtio-net: do not reset vlan filtering at set_features").
This change still preserves the goal of the commit, which was to avoid
resetting the table during migration, by checking whether the
VIRTIO_NET_F_CTRL_VLAN bit of vdev->guest_features is being changed;
vdev->guest_features is set before virtio_net_set_features() gets called
during migration.
It also avoids resetting the table when the driver sets a feature
bitmask with no change for the VIRTIO_NET_F_CTRL_VLAN bit, which makes
the operation idempotent and its semantics cleaner.
Additionally, this change ensures the table is initialized after
feature negotiation and before the DRIVER_OK status bit being set for
compatibility with the Linux driver before commit 50c0ada627f5
("virtio-net: fix race between ndo_open() and virtio_device_ready()"),
which did not ensure to set the DRIVER_OK status bit before modifying
the table.
Fixes: 06b636a1e2 ("virtio-net: do not reset vlan filtering at set_features")
Cc: qemu-stable@nongnu.org
Reported-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Signed-off-by: Akihiko Odaki <odaki@rsg.ci.i.u-tokyo.ac.jp>
Tested-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Message-Id: <20250727-vlan-v3-1-bbee738619b1@rsg.ci.i.u-tokyo.ac.jp>
Tested-by: Konstantin Shkolnyy <kshk@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit b44135daa3 introduced virtqueue_ordered_fill for
VIRTIO_F_IN_ORDER support but had a few issues:
* Conditional while loop used 'steps <= max_steps' but should've been
'steps < max_steps' since reaching steps == max_steps would indicate
that we didn't find an element, which is an error. Without this
change, the code would attempt to read invalid data at an index
outside of our search range.
* Incremented 'steps' using the next chain's ndescs instead of the
current one.
This patch corrects the loop bounds and synchronizes 'steps' and index
increments.
We also add a defensive sanity check against malicious or invalid
descriptor counts to avoid a potential infinite loop and DoS.
Fixes: b44135daa3 ("virtio: virtqueue_ordered_fill - VIRTIO_F_IN_ORDER support")
Reported-by: terrynini <terrynini38514@gmail.com>
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <20250721150208.2409779-1-jonah.palmer@oracle.com>
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Third RISC-V PR for 10.1
* Fix pmp range wraparound on zero
* Update FADT and MADT versions in ACPI tables
* Fix target register read when source is inactive
* Add riscv_hwprobe entry to linux-user strace list
* Do not call GETPC() in check_ret_from_m_mode()
* Revert "Generate strided vector loads/stores with tcg nodes."
* Fix exception type when VU accesses supervisor CSRs
* Restrict mideleg/medeleg/medelegh access to S-mode harts
* Restrict midelegh access to S-mode harts
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmiJbsUACgkQr3yVEwxT
# gBPXCxAAhgcGh/mbdk/DZM4Gx9WqbfjU/1jZR9FCld9im3GLtJfq7IdEcsUZzpNb
# E4sp49lr99qoogKhh3exYhBl0/t0WBoT5mtHNPLFRD3LX2gw6EFQWnD8FN1D//sO
# QvyulomYbmI/Ywf5n5SszF4BpOKh7nyUEZBp4PU6vLT5btsZheSoTyCypH4a7KAy
# GMFNO+O1k6NEwkUqqiIb9Pg8NOp/R3TlNWOjS8fwqyPSU/F8/pzehJQu4WOMAyM8
# eGvqCZiwTg5CcLZfhQZ8dmqJ2qqI44FEzPjyq/Woq5hDmGDMl1iYhgjX5Ozy0X5j
# m4Q+ZH0KIr18EkUD9z4fJbcQAMIm/2b90TShYon6+JYXX8DI8gUCvtg2vgsPAlnS
# M6vgNT25qY8QZa/FbUGcP2+96AlaqX11jUou+TMuJMSr036gTP7gXux5hqYDrd0B
# 4WL1XPcfNZshK5+LAQ+2uwQ9JcKlEaw/mkZHvHgYN7a03UynjCn0oFZtTYvaB4Qx
# Du8Rm9VPlLp3e25VmOiObYyq2Cf6sQXlWomKLJbvfCj217ZXvjOwEjj8hBcg3zJ/
# 6ix/wmDic+YtwmYE7EaGZaExpV5ZjZog61jzMziilZrCJarAoguq0P9tThXGtViX
# TqQcn1V391EfVZYbS3JBO08xmkkX2k7Ia//Th35nByLt7zzrRbs=
# =pKhf
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 29 Jul 2025 21:00:53 EDT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20250730-2' of https://github.com/alistair23/qemu:
target/riscv: Restrict midelegh access to S-mode harts
target/riscv: Restrict mideleg/medeleg/medelegh access to S-mode harts
target/riscv: Fix exception type when VU accesses supervisor CSRs
riscv: Revert "Generate strided vector loads/stores with tcg nodes."
target/riscv: do not call GETPC() in check_ret_from_m_mode()
linux-user/strace.list: add riscv_hwprobe entry
intc/riscv_aplic: Fix target register read when source is inactive
tests/data/acpi/riscv64: Update expected FADT and MADT
hw/riscv/virt-acpi-build.c: Update FADT and MADT versions
bios-tables-test-allowed-diff.h: Allow RISC-V FADT and MADT changes
target/riscv: Fix pmp range wraparound on zero
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
RISC-V AIA Spec states:
"For a machine-level environment, extension Smaia encompasses all added
CSRs and all modifications to interrupt response behavior that the AIA
specifies for a hart, over all privilege levels. For a supervisor-level
environment, extension Ssaia is essentially the same as Smaia except
excluding the machine-level CSRs and behavior not directly visible to
supervisor level."
Since midelegh is an AIA machine-mode CSR, add Smaia extension check in
aia_smode32 predicate.
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jay Chang <jay.chang@sifive.com>
Reviewed-by: Nutty Liu<liujingqi@lanxincomputing.com>
Message-ID: <20250701030021.99218-3-jay.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V Privileged Spec states:
"In harts with S-mode, the medeleg and mideleg registers must exist, and
setting a bit in medeleg or mideleg will delegate the corresponding trap
, when occurring in S-mode or U-mode, to the S-mode trap handler. In
harts without S-mode, the medeleg and mideleg registers should not
exist."
Add smode predicate to ensure these CSRs are only accessible when S-mode
is supported.
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jay Chang <jay.chang@sifive.com>
Reviewed-by: Nutty Liu<liujingqi@lanxincomputing.com>
Message-ID: <20250701030021.99218-2-jay.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We're missing a strace entry for riscv_hwprobe, and using -strace will
report it as "Unknown syscall 258".
After this patch we'll have:
$ ./build/qemu-riscv64 -strace test_mutex_riscv
110182 riscv_hwprobe(0x7f207efdc700,1,0,0,0,0) = 0
110182 brk(NULL) = 0x0000000000082000
(...)
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20250728170633.113384-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V support is added only in ACPI 6.6. According to the ACPI 6.6
specification, the minor version of the Fixed ACPI Description Table
(FADT) should be 6, and the Multiple APIC Description Table (MADT)
should use revision 7. So, update the RISC-V FADT and MADT to reflect
correct versions.
Update the code comments to reflect ACPI 6.6 version details.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Nutty Liu <liujingqi@lanxincomputing.com>
Message-ID: <20250724110350.452828-3-sunilvl@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
pmp_is_in_range() prefers to match addresses within the interval
[start, end]. To archieve this, pmpaddrX is decremented during the end
address update.
In TOR mode, a rule is ignored if its start address is greater than or
equal to its end address.
However, if pmpaddrX is set to 0, this decrement operation causes the
calulated end address to wrap around to UINT_MAX. In this scenario, the
address guard for this PMP entry would become ineffective.
This patch addresses the issue by moving the guard check earlier,
preventing the problematic wraparound when pmpaddrX is zero.
Signed-off-by: Vac Chen <vacantron@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20250706065554.42953-1-vacantron@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The test passed when it was added. However, the commit adding it
neglected to make Meson aware of it, so it never ran automatically.
The test stopped making sense when we changed headings markup, and
ceased to pass then. It should've been removed then. Do that now.
Fixes: 6c10778826 (docs/sphinx: remove special parsing for freeform sections)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20250724091742.1950167-3-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The docs generated for qapi/accelerator.json shows text "=
Accelerators" instead of a heading. This is because the patch that
added the heading crossed with the commit that changed heading
markup (commit 6c10778826 "docs/sphinx: remove special parsing for
freeform sections"). Fix the markup.
Fixes: 18da42ee42 (qapi/accel: Move definitions related to accelerators in their own file)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20250724091742.1950167-2-armbru@redhat.com>
"qemu/error-report.h" was previously implicitly included. This is no
longer the case following 012842c075.
However, the issue predates this change as `error-report.h` should have
been included when the `warn_report` call was introduced.
Fixes: fa140b9562 ("hw/sm501: allow compiling without PIXMAN")
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20250728090518.963573-1-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
A use-after-free bug was reported when booting a Linux kernel during the
pci setup phase. It's quite hard to reproduce (needs smp, and favored by
having several pci devices with BAR and specific Linux config, which
is Debian default one in this case).
After investigation (see the associated bug ticket), it appears that,
under specific conditions, we might access a cached AddressSpaceDispatch
that was reclaimed by RCU thread meanwhile.
In the Linux boot scenario, during the pci phase, memory region are
destroyed/recreated, resulting in exposition of the bug.
The core of the issue is that we cache the dispatch associated to
current cpu in cpu->cpu_ases[asidx].memory_dispatch. It is updated with
tcg_commit, which runs asynchronously on a given cpu.
At some point, we leave the rcu critial section, and the RCU thread
starts reclaiming it, but tcg_commit is not yet invoked, resulting in
the use-after-free.
It's not the first problem around this area, and commit 0d58c66068 [1]
("softmmu: Use async_run_on_cpu in tcg_commit") already tried to
address it. It did a good job, but it seems that we found a specific
situation where it's not enough.
This patch takes a simple approach: remove the cached value creating the
issue, and make sure we always get the current mapping for address
space, using address_space_to_dispatch(cpu->cpu_ases[asidx].as).
It's equivalent to qatomic_rcu_read(&as->current_map)->dispatch;
This is not really costly, we just need two dereferences,
including one atomic (rcu) read, which is negligible considering we are
already on mmu slow path anyway.
Note that tcg_commit is still needed, as it's taking care of flushing
TLB, removing previously mapped entries.
Another solution would be to cache directly values under the dispatch
(dispatch themselves are not ref counted), keep an active reference on
associated memory section, and release it when appropriate (tricky).
Given the time already spent debugging this area now and previously, I
strongly prefer eliminating the root of the issue, instead of adding
more complexity for a hypothetical performance gain. RCU is precisely
used to ensure good performance when reading data, so caching is not as
beneficial as it might seem IMHO.
[1] https://gitlab.com/qemu-project/qemu/-/commit/0d58c660689f6da1e3feff8a997014003d928b3b
Cc: qemu-stable@nongnu.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/3040
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20250724161142.2803091-1-pierrick.bouvier@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In commit cfcacbab38 ("xen/passthrough: use gsi to map pirq when
dom0 is PVH") an `error_report` was added to this file, but the
corresponding include of `qemu/error-report.h` was missed. This
only becomes apparent when building against Xen 4.20+ with trace
backend log disabled.
Fixes: cfcacbab38 (xen/passthrough: use gsi to map pirq when dom0 is PVH)
Signed-off-by: Adam Williamson <awilliam@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20250717220207.171040-1-awilliam@redhat.com>
[PMD: Improved commit description, added Fixes: tag]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to the 'MIPS MT Application-Specific Extension' manual:
If the VPE executing the instruction is not a Master VPE,
with the MVP bit of the VPEConf0 register set, the EVP bit
is unchanged by the instruction.
Modify the DVPE/EVPE opcodes to only update the MVPControl.EVP bit
if executed on a master VPE.
Cc: qemu-stable@nongnu.org
Reported-by: Hansni Bu
Buglink: https://bugs.launchpad.net/qemu/+bug/1926277
Fixes: f249412c74 ("mips: Add MT halting and waking of VPEs")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-ID: <20210427133343.159718-1-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In commit a59d06305f ("vfio/pci: Introduce x-pci-class-code option"),
pci_register_vga() has been moved ouside of vfio_populate_vga(). As a
result, IGD VGA ranges are no longer properly exposed to guest.
To fix this, call pci_register_vga() after vfio_populate_vga() legacy
mode. A wrapper function vfio_pci_config_register_vga() is introduced
to handle it.
Fixes: a59d06305f ("vfio/pci: Introduce x-pci-class-code option")
Signed-off-by: Tomita Moeko <tomitamoeko@gmail.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20250723160906.44941-3-tomitamoeko@gmail.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Regions for sub-page BARs are normally mapped here, in response to the
guest writing to PCI config space:
vfio_pci_write_config()
pci_default_write_config()
pci_update_mappings()
memory_region_add_subregion()
vfio_sub_page_bar_update_mapping()
... vfio_dma_map()
However, after CPR, the guest does not reconfigure the device and the
code path above is not taken. To fix, in vfio_cpr_pci_post_load, call
vfio_sub_page_bar_update_mapping for each sub-page BAR with a valid
address.
Fixes: 7e9f214113 ("vfio/container: restore DMA vaddr")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Link: https://lore.kernel.org/qemu-devel/1752520890-223356-1-git-send-email-steven.sistare@oracle.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Commit 350785d41d ("ramfb: Add property to control if load the
romfile") introduced the `use-legacy-x86-rom` property for the
`vfio-pci-nohotplug` device, allowing control over VGA BIOS ROM
loading. However, the property compatibility setting was incorrectly
applied to the `vfio-pci` device instead, which causes all `vfio-pci`
devices to fail to load. This change fixes the issue by ensuring the
property is set on the correct device.
Fixes: d5fcf0d960 ("hw/i386: Add the ramfb romfile compatibility")
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20250723062714.1245826-1-clg@redhat.com
Signed-off-by: Cédric Le Goater <clg@redhat.com>
documentation and test cleanups
- improve clarity of user-mode docs
- remove reference to TAP tarball
- add new hypervisor test for aarch64 EL2
- reduce combinatorial explosion of plugin tests
- make docker-all-test-cross more friendly to non-x86 hosts
- expose unittests to sysv.args for embedded help
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmiFUdoACgkQ+9DbCVqe
# KkQn+Af/RpTh4XmIcqiLvXrygLWo8hSELS0gjIRZgAA8QyBmojZ+e13los3pzm2Z
# WWlQhh4T0OHgMtZCPPrP+XUc/QDgV3Pt41C1O6SWRwqD4v/7oWNNZz+pFra7x160
# CLBJfcVuRKdFzuR1NZldR8LJufmAMnPnBwE+cV9SpBlGe/lvcLPPvjF0eXQnW1yP
# fWmNgf7VnLBPEQ3NQkliZ23Ku6p4yWDfJLfqgUAXe57Eom1PpDEaPlc+5UaYtAKs
# ee6Gk5CqVFUhIj0v50qBn1giLyaqaXyGn9yWiwiNDL/qVV1v+DK7LNt5B0bTXCfd
# X1KTwpJJdbzmcDftrAq+oacaeXryIA==
# =Sxa/
# -----END PGP SIGNATURE-----
# gpg: Signature made Sat 26 Jul 2025 18:08:26 EDT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* tag 'pull-10.1-rc1-maintainer-260725-1' of https://gitlab.com/stsquad/qemu:
tests/functional: expose sys.argv to unittest.main
tests/docker: handle host-arch selection for all-test-cross
tests/docker: add --arch-only to qemu deps for all-test-cross
tests/tcg: reduce the number of plugin tests combinations
configure: expose PYTHON to test/tcg/config-host.mak
tests/tcg: don't include multiarch tests if not supported
tests/tcg: remove ADDITIONAL_PLUGINS_TESTS
tests/tcg: skip libsyscall.so on softmmu tests
tests/functional: add hypervisor test for aarch64
docs/user: expand section on threading
docs/user: slightly reword section on system calls
docs/user: clean up headings
docs/system: reword the TAP notes to remove tarball ref
docs/user: clarify user-mode expects the same OS
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>