xen_pt_pmcsr_reg_write() needs an adjustment to deal with the RW1C
nature of the not passed through bit 15 (PCI_PM_CTRL_PME_STATUS).
This is a preparatory patch for XSA-131.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
There's no point in xen_pt_pmcsr_reg_{read,write}() each ORing
PCI_PM_CTRL_STATE_MASK and PCI_PM_CTRL_NO_SOFT_RESET into a local
emu_mask variable - we can have the same effect by setting the field
descriptor's emu_mask member suitably right away. Note that
xen_pt_pmcsr_reg_write() is being retained in order to allow later
patches to be less intrusive.
This is a preparatory patch for XSA-131.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Without this the actual XSA-131 fix would cause the enable bit to not
get set anymore (due to the write back getting suppressed there based
on the OR of emu_mask, ro_mask, and res_mask).
Note that the fiddling with the enable bit shouldn't really be done by
qemu, but making this work right (via libxc and the hypervisor) will
require more extensive changes, which can be postponed until after the
security issue got addressed.
This is a preparatory patch for XSA-131.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Limit error messages resulting from bad guest behavior to avoid allowing
the guest to cause the control domain's disk to fill.
The first message in pci_msix_write() can simply be deleted, as this
is indeed bad guest behavior, but such out of bounds writes don't
really need to be logged.
The second one is more problematic, as there guest behavior may only
appear to be wrong: For one, the old logic didn't take the mask-all bit
into account. And then this shouldn't depend on host device state (i.e.
the host may have masked the entry without the guest having done so).
Plus these writes shouldn't be dropped even when an entry is unmasked.
Instead, if they can't be made take effect right away, they should take
effect on the next unmasking or enabling operation - the specification
explicitly describes such caching behavior. Until we can validly drop
the message (implementing such caching/latching behavior), issue the
message just once per MSI-X table entry.
Note that the log message in pci_msix_read() similar to the one being
removed here is not an issue: "addr" being of unsigned type, and the
maximum size of the MSI-X table being 32k, entry_nr simply can't be
negative and hence the conditonal guarding issuing of the message will
never be true.
This is XSA-130.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
It's being used by the hypervisor. For now simply mimic a device not
capable of masking, and fully emulate any accesses a guest may issue
nevertheless as simple reads/writes without side effects.
This is XSA-129.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
The old logic didn't work as intended when an access spanned multiple
fields (for example a 32-bit access to the location of the MSI Message
Data field with the high 16 bits not being covered by any known field).
Remove it and derive which fields not to write to from the accessed
fields' emulation masks: When they're all ones, there's no point in
doing any host write.
This fixes a secondary issue at once: We obviously shouldn't make any
host write attempt when already the host read failed.
This is XSA-128.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
This new C module will be used by ARM machine files to generate
platform bus node and their dynamic sysbus device tree nodes.
Dynamic sysbus device node addition is done in a machine init
done notifier. arm_register_platform_bus_fdt_creator does the
registration of this latter and is supposed to be called by
ARM machine files that support platform bus and their dynamic
sysbus. Addition of dynamic sysbus nodes is done only if the
user did not provide any dtb.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1433244554-12898-2-git-send-email-eric.auger@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After introduction of kvm_arch_msi_data_to_gsi, kvm_gsi_direct_mapping
now can be set on ARM. Also kvm_msi_via_irqfd_allowed can be set,
depending on kernel irqfd support, hence enabling VIRTIO-PCI with
vhost back-end.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On ARM the MSI data corresponds to the shared peripheral interrupt (SPI)
ID. This latter equals to the SPI index + 32. to retrieve the SPI index,
matching the gsi, an architecture specific function is introduced.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for adding the GICv2m which requires address specifiers
and is a subnode of the gic, we extend the gic DT definition to specify
the #address-cells and #size-cells properties and add an empty ranges
property properties of the DT node, since this is required to add the
v2m node as a child of the gic node.
Note that we must also expand the irq-map to reference the gic with the
right address-cells as a consequence of this change.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-4-git-send-email-christoffer.dall@linaro.org
Suggested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio-input: two small fixups
# gpg: Signature made Tue Jun 2 09:32:51 2015 BST using RSA key ID D3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>"
* remotes/kraxel/tags/pull-input-20150602-1:
virtio-input: make virtio devices follow usual naming convention
virtio-input: const_le16 and const_le32 not build time constant
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pc build fix
My last pull breaks build on systems with iasl.
Fix this up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jun 1 20:41:08 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
acpi: add missing ssdt
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As the implementation of const_le16 and const_le32 is not build time constant
on big endian systems this need to be fixed.
CC hw/input/virtio-input-hid.o
hw/input/virtio-input-hid.c:340:13: error: initializer element is not constant
hw/input/virtio-input-hid.c:340:13: error: (near initialization for ‘virtio_keyboard_config[1].u.ids.bustype’)
...
Signed-off-by: Michael Mueller <mimu@linux.vnet.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The previous commits narrowed use of QError to handle_qmp_command()
and its helpers monitor_protocol_emitter(), build_qmp_error_dict().
Narrow it further to just the command handler call: instead of
converting Error to QError throughout handle_qmp_command(), convert
the QError gotten from the command handler to Error, and switch the
helpers from QError to Error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
pcie_aer_inject_error's implementation is split into the
hmp_pcie_aer_inject_error() and pcie_aer_inject_error_print(). The
former is a peculiar crossbreed between HMP and QMP handler. On
success, it works like a QMP handler: store QDict through ret_data
parameter, return 0. Printing the QDict is left to
pcie_aer_inject_error_print(). On failure, it works more like an HMP
handler: print error to monitor, return negative number.
To convert to the traditional interface, turn
pcie_aer_inject_error_print() into a command handler wrapping around
hmp_pcie_aer_inject_error(). By convention, this command handler
should be called hmp_pcie_aer_inject_error(), so rename the existing
hmp_pcie_aer_inject_error() to do_pcie_aer_inject_error().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For device_add, that's easy: just wrap the obvious hmp_device_add()
around do_device_add().
monitor_user_noop() is now unused, drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For drive_del, that's easy: hmp_drive_del() sheds its unused last
parameter, and its return value, which the caller ignored anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Protocol must be spice, vnc isn't implemented. Fix up documentation.
Attempts to use vnc or any other unknown protocol yield the misleading
error message "Invalid parameter 'protocol'". Improve it to
"Parameter 'protocol' expects spice".
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by. Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Inline qmp_call_cmd() along with its helper handler_audit() into its
only caller handle_qmp_command(), and simplify the result.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Jan Beulich