On Xen MSIs can be remapped into pirqs, which are a type of event
channels. It's mostly for the benefit of PCI passthrough devices, to
avoid the overhead of interacting with the emulated lapic.
However remapping interrupts and MSIs is also supported for emulated
devices, such as the e1000 and virtio-net.
When an interrupt or an MSI is remapped into a pirq, masking and
unmasking is done by masking and unmasking the event channel. The
masking bit on the PCI config space or MSI-X table should be ignored,
but it isn't at the moment.
As a consequence emulated devices which use MSI or MSI-X, such as
virtio-net, don't work properly (the guest doesn't receive any
notifications). The mechanism was working properly when xen_apic was
introduced, but I haven't narrowed down which commit in particular is
causing the regression.
Fix the issue by ignoring the masking bit for MSI and MSI-X which have
been remapped into pirqs.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Current intel_iommu only supports 4K page which may not be sufficient
to cover guest working set. This patch tries to enable 2M and 1G mapping
for intel_iommu. This is also useful for future device IOTLB
implementation to have a better hit rate.
Major work is adding a page mask field on IOTLB entry to make it
support large page. And also use the slpte level as key to do IOTLB
lookup. MAMV was increased to 18 to support direct invalidation for 1G
mapping.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The 'base' field of MemoryHotplugState is ram_addr_t, which indicates that
it exists in the abstract address space of RAM regions.
However, the actual usage of this field indicates that it is a concrete
physical address (it's passed as an offset to memory_region_add_subgregion
for example).
So, correct its type to 'hwaddr'.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
The struct is not used for anything, now.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The code can use the PCMachineClass.pci_enabled field directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
The ACPI code can use the PCMachineState fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Remove the fields: legacy_acpi_table_size, has_acpi_build,
has_reserved_memory, and rsdp_in_ram from PcGuestInfo, and let
the existing code use the PCMachineClass fields directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We don't need to save the pointer on AcpiBuildState, as it is not
used anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can use PC_MACHINE(qdev_get_machine())->acpi_guest_info to get
guest_info.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
We can get the PcGuestInfo struct directly from PCMachineState,
and the return value is not needed at all.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Instead of allocating a new struct just for PcGuestInfo and the
mchine_done Notifier, place them inside PCMachineState.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
>From the specs (20.8 Get Device GUID Command), the command needs to
return a GUID (Globally Unique ID), or UUID, that should never change
over the lifetime of the device. qemu_uuid looked like a good
candidate to start with but we could use a specific BMC property also
if needed.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently, sdr attributes are identified using byte offsets and this
can be a bit confusing.
This patch adds a struct ipmi_sdr_compact conforming to the IPMI specs
and replaces byte offsets with names. It also introduces and uses a
struct ipmi_sdr_header in sections of the code where no assumption is
made on the type of SDR. This leave rooms to potential usage of other
types in the future.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The IPMI BMC simulator populates the SDR table with a set of initial
SDRs. The length of each SDR is taken from the record itself (byte 4)
which does not include the size of the header. But, the full length
(header + data) is required by the sdr_add_entry() routine.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ARRAY_SIZE() is simple to use and removes the need to pre-define
the size of the command arrays.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Each routine using the IPMI_ADD_RSP_DATA, IPMI_CHECK_CMD_LEN or
IPMI_CHECK_RESERVATION macros needs to define a goto label 'out' to
handle hidden errors. Using directly a return statement has the same
effect and it removes the fact that 'out' needs to be defined.
The code exits in ipmi_sim_handle_command() are a little different
from the rest and a "possible" error in the macro IPMI_ADD_RSP_DATA is
handled before making use of it. This might be a bit excessive as a
minimum response len is currently 300 bytes and the patch checks that
at least 3 are available.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCI devices can't be plugged directly into PCI extra root bridges
because their resources can't be computed by firmware before the ACPI
tables are loaded.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The mechanism to get the option ROM for virtio-net does not block the
PCI ROM from being loaded. Therefore, in vhost-user-test there are
two entries in the boot menu for the virtio-net card: one as an
embedded option ROM, one from the ROM BAR.
The embedded option ROM in vhost-user-test is the non-EFI-enabled,
while the ROM BAR has an EFI-enabled ROM. The two are compiled with
slightly different parameters, where only the old BIOS-only one doesn't
have a timeout for the "Press Ctrl-B" banner. When using a new
machine type, therefore, the vhost-user-test has to wait for the
EFI-enabled ROM's banner to go away. There are several ways to fix
this:
1) fix the ROMs to have the same configuration
2) add ",romfile=" to the -device line
3) remove --option-rom and add the ROM file name to the -device line
4) use an old machine type
This patch chooses 3. In addition, the file name was wrong because
qtest runs QEMU relative to the top build directory, not to the
x86_64-softmmu/ subdirectory, which is fixed too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The virtqueue_pop() implementation needs to check if the avail ring
contains some pending buffers. To perform this check, it is not
always necessary to fetch the avail_idx in the VQ memory, which is
expensive. This patch introduces a shadow variable tracking avail_idx
and modifies virtio_queue_empty() to access avail_idx in physical
memory only when necessary.
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Message-Id: <b617d6459902773d9f4ab843bfaca764f5af8eda.1450218353.git.v.maffione@gmail.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Compared to vring, virtio has a performance penalty of 10%. Fix it
by combining all the reads for a descriptor in a single address_space_read
call. This also simplifies the code nicely.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Build the addresses and s/g lists on the stack, and then copy them
to a VirtQueueElement that is just as big as required to contain this
particular s/g list. The cost of the copy is minimal compared to that
of a large malloc.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Build the addresses and s/g lists on the stack, and then copy them
to a VirtQueueElement that is just as big as required to contain this
particular s/g list. The cost of the copy is minimal compared to that
of a large malloc.
When virtqueue_map is used on the destination side of migration or on
loadvm, the iovecs have already been split at memory region boundary,
so we can just reuse the out_num/in_num we find in the file.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allocate the arrays for in_addr/out_addr/in_sg/out_sg outside the
VirtQueueElement. For now, virtqueue_pop and vring_pop keep
allocating a very large VirtQueueElement.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Move allocation to virtio functions also when loading/saving a
VirtQueueElement. This will also let the load/save functions
keep backwards compatibility when the VirtQueueElement layout
is changed.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The return code of virtqueue_pop/vring_pop is unused except to check for
errors or 0. We can thus easily move allocation inside the functions
and just return a pointer to the VirtQueueElement.
The advantage is that we will be able to allocate only the space that
is needed for the actual size of the s/g list instead of the full
VIRTQUEUE_MAX_SIZE items. Currently VirtQueueElement takes about 48K
of memory, and this kind of allocation puts a lot of stress on malloc.
By cutting the size by two or three orders of magnitude, malloc can
use much more efficient algorithms.
The patch is pretty large, but changes to each device are testable
more or less independently. Splitting it would mostly add churn.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This moves the Travis tests from the legacy VM infrastructure (which
only seems to run 5-6 jobs at once) to the new container based approach.
The principle difference is there is no sudo in the containers so all
packages are installed using the apt add-on. This means one of the build
combinations can be dropped as it was only for checking the build with
additional packages.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Migration pull req.
Small fixes, nothing major.
# gpg: Signature made Fri 05 Feb 2016 13:51:30 GMT using RSA key ID 854083B6
# gpg: Good signature from "Amit Shah <amit@amitshah.net>"
# gpg: aka "Amit Shah <amit@kernel.org>"
# gpg: aka "Amit Shah <amitshah@gmx.net>"
* remotes/amit-migration/tags/migration-for-2.6-2:
migration: fix bad string passed to error_report()
static checker: e1000-82540em got aliased to e1000
migration: remove useless code.
qmp-commands.hx: Document the missing options for migration capability commands
qmp-commands.hx: Fix the missing options for migration parameters commands
migration/ram: Fix some helper functions' parameter to use PageSearchStatus
savevm: Split load vm state function qemu_loadvm_state
migration: rename 'file' in MigrationState to 'to_dst_file'
ram: Split host_from_stream_offset() into two helper functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We didn't document x-cpu-throttle-initial/x-cpu-throttle-increment for
commands migrate-set-parameters and query-migrate-parameters.
Here we add the descriptions for these two options and fix the wrong example
for query-migrate-parameters qmp commands.
Besides, this will also fix the bug that we can't set x-cpu-throttle-initial
and x-cpu-throttle-increment through migrate-set-parameters qmp command.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1452829066-9764-6-git-send-email-zhang.zhanghailiang@huawei.com>
[Amit: fix typo in 'auto-converge']
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Stefano Stabellini