* New "raspi3" machine emulating RaspberryPi 3
* Fix bad register definitions for VMIDR and VMPIDR (which caused
assertions for 64-bit guest CPUs with EL2 on big-endian hosts)
* hw/char/stm32f2xx_usart: fix TXE/TC bit handling
* Fix ast2500 protection register emulation
* Lots of SD card emulation cleanups and bugfixes
# gpg: Signature made Thu 22 Feb 2018 15:18:53 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180222: (32 commits)
sdcard: simplify SD_SEND_OP_COND (ACMD41)
sdcard: simplify SEND_IF_COND (CMD8)
sdcard: warn if host uses an incorrect address for APP CMD (CMD55)
sdcard: check the card is in correct state for APP CMD (CMD55)
sdcard: handles more commands in SPI mode
sdcard: use a more descriptive label 'unimplemented_spi_cmd'
sdcard: handle the Security Specification commands
sdcard: handle CMD54 (SDIO)
sdcard: use the registerfields API for the CARD_STATUS register masks
sdcard: use the correct masked OCR in the R3 reply
sdcard: simplify using the ldst API
sdcard: remove commands from unsupported old MMC specification
sdcard: clean the SCR register and add few comments
sdcard: fix the 'maximum data transfer rate' to 25MHz
sdcard: update the CSD CRC register regardless the CSD structure version
sdcard: Don't always set the high capacity bit
sdcard: use the registerfields API to access the OCR register
sdcard: use G_BYTE from cutils
sdcard: define SDMMC_CMD_MAX instead of using the magic '64'
sdcard: add more trace events
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To comply with Spec v1.10 (and 2.00, 3.01):
. TRAN_SPEED
for current SD Memory Cards that field must be always 0_0110_010b (032h) which is
equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-4-f4bug@amsat.org
[PMM: fixed comment indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some register blocks of the ast2500 are protected by protection key
registers which require the right magic value to be written to those
registers to allow those registers to be mutated.
Register manuals indicate that writing the correct magic value to these
registers should cause subsequent reads from those values to return 1,
and writing any other value should cause subsequent reads to return 0.
Previously, qemu implemented these registers incorrectly: the registers
were handled as simple memory, meaning that writing some value x to a
protection key register would result in subsequent reads from that
register returning the same value x. The protection was implemented by
ensuring that the current value of that register equaled the magic
value.
This modifies qemu to have the correct behaviour: attempts to write to a
ast2500 protection register results in a transition to 1 or 0 depending
on whether the written value is the correct magic. The protection logic
is updated to ensure that the value of the register is nonzero.
This bug caused deadlocks with u-boot HEAD: when u-boot is done with a
protectable register block, it attempts to lock it by writing the
bitwise inverse of the correct magic value, and then spinning forever
until the register reads as zero. Since qemu implemented writes to these
registers as ordinary memory writes, writing the inverse of the magic
value resulted in subsequent reads returning that value, leading to
u-boot spinning forever.
Signed-off-by: Hugo Landau <hlandau@devever.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180220132627.4163-1-hlandau@devever.net
[PMM: fixed incorrect code indentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I/O currently being synchronous, there is no reason to ever clear the
SR_TXE bit. However the SR_TC bit may be cleared by software writing
to the SR register, so set it on each write.
In addition, fix the reset value of the USART status register.
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
[PMM: removed XXX tag from comment, since it isn't something
we need to come back and fix in QEMU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds a "raspi3" machine type, which can now be selected as
the machine to run on by users via the "-M" command line option to QEMU.
The machine type does *not* ignore memory transaction failures so we
likely need to add some dummy devices later when people run something
more complicated than what I'm using for testing.
Signed-off-by: Pekka Enberg <penberg@iki.fi>
[PMM: added #ifdef TARGET_AARCH64 so we don't provide the 64-bit
board in the 32-bit only arm-softmmu build.]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The register definitions for VMIDR and VMPIDR have separate
reginfo structs for the AArch32 and AArch64 registers. However
the 32-bit versions are wrong:
* they use offsetof instead of offsetoflow32 to mark where
the 32-bit value lives in the uint64_t CPU state field
* they don't mark themselves as ARM_CP_ALIAS
In particular this means that if you try to use an Arm guest CPU
which enables EL2 on a big-endian host it will assert at reset:
target/arm/cpu.c:114: cp_reg_check_reset: Assertion `oldvalue == newvalue' failed.
because the reset of the 32-bit register writes to the top
half of the uint64_t.
Correct the errors in the structures.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
---
This is necessary for 'make check' to pass on big endian
systems with the 'raspi3' board enabled, which is the
first board which has an EL2-enabled-by-default CPU.
This is the re-factor of softfloat:
- shared common code path float16/32/64
- well commented and easy to follow code
- added a bunch of float16 support
While some operations are slower the key ones exercised by the
floating point dbt-bench are the same: https://i.imgur.com/oXNJNql.png
# gpg: Signature made Wed 21 Feb 2018 10:44:14 GMT
# gpg: using RSA key FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>"
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-softfloat-refactor-210218-1: (22 commits)
fpu/softfloat: re-factor sqrt
fpu/softfloat: re-factor compare
fpu/softfloat: re-factor minmax
fpu/softfloat: re-factor scalbn
fpu/softfloat: re-factor int/uint to float
fpu/softfloat: re-factor float to int/uint
fpu/softfloat: re-factor round_to_int
fpu/softfloat: re-factor muladd
fpu/softfloat: re-factor div
fpu/softfloat: re-factor mul
fpu/softfloat: re-factor add/sub
fpu/softfloat: define decompose structures
fpu/softfloat: move the extract functions to the top of the file
fpu/softfloat: improve comments on ARM NaN propagation
include/fpu/softfloat: add some float16 constants
include/fpu/softfloat: implement float16_set_sign helper
include/fpu/softfloat: implement float16_chs helper
include/fpu/softfloat: implement float16_abs helper
target/*/cpu.h: remove softfloat.h
fpu/softfloat-types: new header to prevent excessive re-builds
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pass the modifier state to the keymap lookup function. In case multiple
keysym -> keycode mappings exist look at the modifier state and prefer
the mapping where the modifier state matches.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20180222070513.8740-6-kraxel@redhat.com
The cursor dmabuf can be NULL, in case no cursor defined by the guest.
Happens for example when linux guests show the framebuffer console.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180220110433.20353-3-kraxel@redhat.com
After some hotkey was pressed sdl2 doesn't forward the first modifier
keyup event to the guest, resulting in stuck modifier keys.
Fix the logic in handle_keyup(). Also gui_key_modifier_pressed doesn't
need to be a global variable.
Reported-by: Howard Spoelstra <hsp.cat7@gmail.com>
Tested-by: Howard Spoelstra <hsp.cat7@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20180220150444.784-1-kraxel@redhat.com
Move the TPM TIS related register and flag #defines into
include/hw/acpi/tpm.h for access by the test case.
Write a test case that covers the TIS functionality.
Add the tests cases to the MAINTAINERS file.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
This is a little bit of a departure from softfloat's original approach
as we skip the estimate step in favour of a straight iteration. There
is a minor optimisation to avoid calculating more bits of precision
than we need however this still brings a performance drop, especially
for float64 operations.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Richard Henderson
